Are you looking for the best way to get rid of lead from your drinking water? If yes, then you should consider buying a water filter.

Lead poisoning is a serious health issue. The good thing is that you don’t have to spend a fortune to get a high-quality water filter. In fact, you can easily find affordable options at your local store.

Lead is a toxic metal found naturally in the earth’s crust. It’s also present in some minerals such as iron, copper, zinc, tin, and silver.

When these metals come into contact with air or water, they release lead particles. These particles can enter our bodies through our skin, mouth, nose, eyes, and lungs.

They can cause severe health problems such as brain damage, kidney failure, and even death.

A water filter removes lead from tap water. There are two types of filters: point-of-use (POU) and point-of-entry (POE).

POU filters are installed directly at the faucet where the water comes out. POE filters are placed before the water enters the house.

Both types of filters are effective in removing lead. However, there are pros and cons associated with each type. Read on to learn more about them.

The most common method used by people to remove lead from their homes is to install a whole-house water filtration system.

Whole-house systems usually consist of a large tank that stores water until it is needed. 

This system is connected to all plumbing fixtures throughout the home. As soon as the water passes through the pipes, it flows through a carbon block which absorbs any contaminants.

After passing through the carbon block, the water goes through a filter cartridge. Once this cartridge has been filled up, it needs to be replaced.

Here in our guide, we’ve found some of the best water filters to remove lead from your water.

With the help of these, you won’t have to worry about lead in your water causing you problems again!

Frizzlife Under Sink Water Filter

The Frizzlife Under Sink Water Filter is a fantastic option if you’re looking for a deep filtration that can remove more than just lead from your water.

It can remove up to 99% of all contaminants from your drinking water. The SK99 compound filter cartridges use a 7 layer filtration process to filter out all the bits you don’t want to drink.

The Frizzlife’s under-sink design makes it easy to replace the filter cartridge and access your filter, without it being too big or clunky to be in the way.

The Frizzlife has excellent water pressure, and can even help yours if it’s quite low. It has a flow rate of 2.0 gallons per minute.

In fact, this filter has such great water pressure that it can fill an 11oz cup of water in 3 seconds flat. 

If you’re looking for an inexpensive solution to lead removal, the Frizzlife Under Sink Water Filter might be what you need.

It uses a carbon block and ion exchange filtration system to ensure that your water is safe to drink.

It uses 3 stages of filtration, putting the water through 6 layers of decontamination, with a layer specifically designed to draw out lead.

Not only that but the Frizzlife filter is super easy to install! You won’t need any professional help. This filter is made to be installed by its users.

Using the helpful YouTube instructional video, along with an included instruction manual, you can get this baby installed in less than 10 minutes.

And changing out the filters every couple of months will only take a few seconds!

Speaking of changing out the filter, Frizzlife has innovated on cartridge and filter changes to give you a more cost-effective filtration system.

Instead of throwing away the whole filter, you only have to dispose of the inner core of it.

This means less waste and much cheaper replacement filters. This means you spend less over time than if you had a more wasteful filter.

Pros

  • Less waste when replacing filters
  • More cost-effective overtime
  • Lead removal specific layer
  • Excellent water pressure
  • Compact size, it won’t be in the way

Cons

  • Filters will have to be replaced every few months or when clogged

Also available from

Home Master TMHP HydroPerfection Undersink RO Water Filter

The Home Master TMHP HydroPerfection Undersink RO Water Filter uses reverse osmosis to provide thorough decontamination of your drinking water.

With a capacity of 1 gallon per minute, you’ll never run out of filtered water. Its compact design allows you to place it wherever you like, whether it’s in the kitchen sink or bathroom sink.

One of the best things about this filter is how easy it is to change. All you need is a standard household vacuum cleaner hose, and you can easily switch out the filter cartridge.

No tools are required. Just unscrew the old one, screw in the new one, and plug it back in. That’s it.

The Home Master TMHP HydroPerfection Undersink RO Water Filter uses 9 stages of filtration to purify water.

Some stages it runs the water through are filtrations, purification, and sterilization using UV light to remove 99% of bacteria and contaminants like chloramines, lead, fluoride, and heavy metals. 

The built-in non-electric permeate pump is a unique feature that reduces water waste and reduces TDS creep.

TDS creep refers to the initial rise of water when the reverse osmosis machine begins working.

This also means that the filter doesn’t require electricity so it won’t add to your bills.

In fact, it may even help reduce them since you’ll be using water a lot more efficiently, 

This filter also comes with a 5-year warranty. If there is a problem with the product, they will repair or replace it free of charge.

If you’re looking for an affordable, reliable, and efficient water filter, then look no further.

The Home Master TMHP HydroPerfection UnderSink Reverse Osmosis Water Filter is a great option.

Pros

  • Easy to use
  • Non-electric
  • Low maintenance
  • Great price
  • Longer life span

Cons

  • Not as effective as some other models
  • Filter needs to be changed once a month
  • No indicator lights

Also available from

iSpring Whole House Water Filter System

The iSpring Whole House Water Filter System is a behemoth of a filter. It’s designed to filter out the water of the whole house in under a few seconds.

It has two chambers separated by a membrane that prevents any particles from passing between them. One chamber filters chlorine while the other filters out lead and other harmful elements.

It has a maximum flow rate of 2 gallons per minute. This makes it perfect for large households who don’t want to wait for their water to get purified.

You can also adjust the pressure to ensure that it fits into your home’s plumbing system.

You can check the quality of the water at all times thanks to its LED display. There are four different levels of water quality displayed on the screen. You can also set up alerts if the water gets too dirty.

With a lifetime warranty and a 10-year manufacturer’s guarantee, you know that this filter will last you a long time. If there is a defect with the unit, they will fix it without charging you.

There are many benefits to owning an iSpring Whole House Water Filter System. First off, it’s very easy to install.

All you have to do is screw it into place. Then connect the hoses and turn on the power. Once everything is connected, you just need to run the water until the filter is full.

Another benefit is that it removes almost all types of impurities from your water. Chlorine, lead, arsenic, mercury, cadmium, nitrates, and fluoride are all filtered out of the water before it reaches your faucets.

However, there are a couple of drawbacks to owning one of these units. For starters, because it holds so much water, it takes up quite a bit of space.

This means that you’ll either need to drill holes through walls or move things around. Another drawback is that it only lasts about five years. After that, you’ll need to buy a new unit.

Overall, though, the iSpring Whole House Water Filters System is a good choice if you’re looking for a powerful yet compact way to purify your entire household’s water.

Pros

  • Easy installation
  • Removes most contaminants
  • Great flow rate
  • Water pressure will not be affected

Cons

  • Only lasts 5 years

 Also available from

Waterdrop Whole House Water Filter System

Waterdrop Whole House Water Filter System is an excellent and compact filter to remove lead from your water.

It has all the power of the iSpring, without taking up as much space. The difference is that it uses gravity instead of pumps to push the water through the filter.

This allows it to fit into smaller spaces than the iSpring. It doesn’t take up nearly as much room since it’s only a few inches tall. However, it does require more maintenance than the iSpring.

When you first use the Water Drop, you must add a small amount of baking soda to the tank.

This helps prevent clogs and maintain the filtration process. Every month, you should change the water in the tank.

If you live in a city where the water contains high amounts of lead, then this may be the best option for you. It’s made of stainless steel which won’t rust.

It comes with a 1-year warranty against defects. Moreover, the filter helps to soften water and will improve your overall health over time. 

If you want to get rid of chlorine, sediment, and lead but don’t mind having to replace the filter every few months, then this could be the perfect solution for you.

Pros

  • Easy to install
  • Removes chlorine and sediment
  • Compact size

Cons

  • Requires monthly replacement

Also available from

Brita Basic Faucet Water Filter

You may have heard of Brita filters before. Typically, they’re known for the filtration jugs which are great at removing contaminants as you drink. The Brita Basic Faucet Water Filter is a fresher take on filtration. 

Made by Brita, with the same thorough filtration in mind that they use for all their filters, this faucet accessory is designed to cleanse your water as it flows from the tap.

The idea behind this is that you can keep your kitchen water free of germs and bacteria.

The system doesn’t work like other Brita Jug filters. It’s designed for continuous use. Simply attach it to the faucet and turn it on.

The water will flow through the faucet, through the filter, and then into your cup. Should the water stop flowing, or there’s a drop in the pressure, then you should replace the filter. That’s when you know the filter is done. 

It’s easy to set up and operate. Simply attach the attachment to your faucet and plug it in.

Once it’s installed, you’ll never have to worry about dirty or contaminated water ever again- or at least until it’s time to replace the filter. 

There are two different versions available. One is white and one is chrome. There are also two different styles. Complete and Basic.

The difference between the two is that the complete option comes with three different spray settings as well. But both work well at removing contaminants and bacteria.

Pros

  • Simple design
  • Easily accessible
  • Filters out contaminants and bacteria
  • Affordable

Cons

  • Must replace whole filtration unit instead of just filter or cartridge every few months

Also available from

Wingsol Under Sink Water Filter

Wingsol Under Sink Water Filter
$56.99


Buy Now
02/18/2024 11:35 pm GMT

Wingsol Under Sink Water Filter is a 5 in 1 multifunction filter. As well as filtering the water, it will soften it as well.

This makes it ideal for people who live in areas where hard water is common. In addition, it has an automatic shut-off feature so you won’t need to worry about running out of hot water while you shower.

This product was made using NSF-certified materials and meets NSF standards for chlorine removal and taste & odor control. It’s safe for drinking and dishwasher use.

The filter uses a dual-stage process to remove chlorine and sediment. First, the filter removes chlorine using activated carbon technology.

Then, the second stage softens the water using ion-exchange resin.

Once the water passes through the filter, it goes through a series of chambers where it gets softened.

These chambers help to reduce any harsh minerals and impurities. It’s great for removing lead.

After passing through these chambers, the water is ready to be used. You can choose from four different spray heads including a standard, a fine mist, a wide stream, and a powerful jet.

To ensure that the filter works properly, you must change the cartridge once a month or so. If you don’t do this, the filter could clog.

This product is built to last. It features a lifetime warranty against defects in material and craftsmanship.

Pros

  • Removes chlorine, lead, and sediments
  • Automatic shut off feature
  • Easy to install
  • Safe for drinking and dishwasher usage

Cons

  • Expensive

Also available from

Pentair FreshPoint Easy Flow Undersink Water Filter System

The Pentair FreshPoint Easy Flow Undersink Water Filter System is easy to install and NSF/ANSI certified. That’s how you know it does a good job!

It features a dual-stage filtration system that includes a pre-filter and a carbon block filter.

The pre-filter helps to remove particles such as dirt and rust before they get into the main filter. Once the water enters the main filter, it gets filtered again by the carbon block filter.

It comes with two replacement cartridges. One cartridge contains a pre-filter and another one contains the carbon block filter. Both are NSF/ANSI Certified.

You can also add a third cartridge if you want to remove more contaminants. You should replace the filters every 6 months to 1 year depending on your local water quality. 

If you have hard water, you might want to consider getting a reverse osmosis (RO) unit.

They’re much better at removing calcium and magnesium than carbon block filters like this system.

However, the carbon block filter is excellent at removing lead contamination.  The carbon block filters are long-lasting and can last up to 3,000 gallons of filtration.

It has a high flow rate of 2.2 gallons per minute. The only drawback is that the filter is battery-powered.

This means as well as having to replace the filters, you’ll also have to replace the batteries when they run out as well.

Pros

  • Easy to install
  • NSF/ANSI certified
  • Dual-stage filtration
  • Compatible with RO systems

Cons

  • Battery-powered so batteries will need replacing as well as the cartridges.

Also available from

APEC Water Systems ROES-50 Essence Series Filter System

The APEC Water Filter System is an excellent choice for drinking water purification.

Its 5-stage filtration process removes chlorine, fluoride, heavy metals, bacteria, viruses, and other impurities from tap water.

This system provides safe drinking water in less time compared to other systems.

It uses a multi-layer filtration technology that makes sure that all harmful substances are removed from the water.

It has a large capacity of 50 gallons. It takes about 4 hours to fill the tank. However, it can be used for up to 12 hours after filling.

There are three different types of filters included in this system. A prefilter, a carbon block filter, and a post-filter. All these filters work together to provide safe drinking water.

The prefilter helps reduce any dirt particles before they reach the carbon block filter. The carbon block filter then removes bad odors and tastes. Finally, the post-filter removes any remaining contaminants.

The APEC Water Filter is easy to use. Just turn on the faucet and let the water run through the whole system. In just a few minutes, you’ll get clean drinking water.

There are no chemicals or hazardous materials used in its manufacturing process. It is made of BPA-free plastic material.

There are several benefits associated with using this product. First, it reduces the amount of time required to purify water. Second, it provides safe drinking water. Third, it is affordable.

This system is compatible with reverse osmosis systems. You don’t have to worry about compatibility issues if you already own one.

Pros

  • Affordable
  • Easy to use
  • Provides safe drinking water
  • Decontaminates water efficiently, particularly good at removing lead

Cons

  • Pricey

Also available from

Santevia Gravity Water System Countertop Model

Santevia Gravity Water System
$225.00


Buy Now
02/19/2024 01:30 am GMT

The Santevia Gravity Water System is a little different from our previous suggestions because it’s a countertop model.

A counter model differs from an under-sink, faucet, or whole house system because it doesn’t require plumbing. This means there are fewer parts involved, which makes installation easier.

If you’re looking for a simple way to get your home ready for summer, then this might be the best option for you.

With this system, you won’t need to buy additional equipment like a water softener. It also works well when combined with a reverse osmosis system.

You will only need to install two components. One is a gravity feed valve, and the other is a water storage container.

The gravity feed valve connects directly to your existing water supply line. When you press the button, the water flows into the storage container.

When you want to drink the water, simply lift the lid off the storage container. No more waiting around for the tap to fill up!

It comes with everything needed to set up the system. You can even add a water dispenser to make life easier. The storage container has a capacity of 1,000 gallons. It holds enough water for up to five people.

The manufacturer recommends replacing the carbon filter every six months. If you do not take care of it properly, it could clog up.

The system includes a stainless steel tank. It’s made of food-grade 304 material. It’s BPA-free.

There’s no need to wait for the water to come out of the tap. With this system, you can start enjoying fresh, clean water immediately.

Pros

  • No need to purchase any additional equipment
  • Works well with a reverse osmotic system
  • Simple design
  • Easy to install

Cons

  • Only has a limited capacity for filtration
  • Needs to be refilled

Also available from

Buyer’s Guide

There’s only so much you can read about water filters before going, huh? Sometimes there’s a lot of jargon and things you don’t quite understand.

In this buyer’s guide, we’ll tell you about all the things you need to know about water filters before buying one.

NSF/ANSI

When buying a water filter, you might often see these letters; NSF/ANSI. But what exactly do they mean?

These letters stand for National Sanitary Foundation/American National Standards Institute.

They ensure that products meet certain standards. These standards include how effective the product is at removing contaminants.

In order to pass the standard, a product must remove 99.99% of bacteria and viruses.

It should also remove chlorine, lead, copper, mercury, arsenic, cadmium, chromium, nickel, iron, maganese, zinc, bromine, fluoride, nitrate, nitrite, radon, selenium, silver, silica, and many others.

This is why it’s important to look for NSF/ANSI-certified products. We’ve found several on Amazon.

Capacity

Another thing to consider when choosing a water filter is its capacity. How big is it? A bigger capacity means you can store more water in the same space.

If you have kids or pets, you may want something with a larger capacity. For example, if you plan on having guests over, a 10-gallon capacity would work great.

However, if you live alone and rarely have company, then a smaller capacity might be better.

This is because you wouldn’t have to worry about running out of water, and you can save yourself a few bucks by choosing something more modest in stature.

Filter Type

A filter type refers to how the water passes through it. There are different types of filters available. Each one has its pros and cons.

One of the most common types of filters is activated carbon. Activated carbon is used to absorb impurities from the water. However, it does require regular cleaning.

Reverse osmosis systems use pressure to force water through membranes. This process removes almost all harmful contaminants. It’s very effective but requires a large amount of energy.

Distillation systems use heat to boil water into steam. Then, the steam condenses back into liquid form. Distillation systems are usually expensive.

Best Filter For Lead Removal

Different types of filters are good for removing different kinds of contaminants.

So which kind of filter is the best at removing lead contaminants? Well, that depends on your needs.

For example, if you’re concerned about lead levels in your drinking water, you’d probably want to get a filter that removes lead. Some great filter types for removing lead are:

Activated Carbon Filters

These are the most popular type of filters. They’re made up of granules of carbon. The carbon absorbs impurities like heavy metals such as lead.

Generally speaking, it’s recommended that you change your filter every 6 months, but some products may require replacing before or after a 6 month period.

Best Water Filter To Remove Lead copy 7

Carbon Block Filters

These are similar to activated carbon filters. Instead of using granules, however, they use blocks of carbon.

They’re not as efficient as activated carbon filters, but they’ll still get the job done!

PVC Membrane Filters

These are other types of filters. PVC stands for polyvinyl chloride. They’re made up of plastic membranes.

The membrane acts as a barrier between water and air. When the water passes through the membrane, it gets filtered — no more lead!

Frequently Asked Questions

In this frequently asked questions section, we’ll answer some of the most popular questions that come to mind about water filters, and the best ones for removing lead.

  • How Do I Know What Size Filter I Need?

    You don’t necessarily need to buy a specific size. If you’re looking for a general rule, though, you should go by the gallons per minute (GPM). For example, a 5 GPM filter will allow you to fill your sink in five hours.

    If you’re planning on doing a lot of cooking, you may want to consider getting a bigger filter. A 10 GPM filter will last longer than a 5 GPM filter. There isn’t an exact rule when it comes to choosing the right size. But generally speaking, you should choose a filter based on how much water you use.

     

  • What's The Difference Between A Reverse Osmosis System And An Activated Carbon Filter?

    Both reverse osmosis and activated carbon filters remove the bad stuff from the water. But each one works differently.

    With a reverse osmosis filter, the water goes through a series of membranes. These membranes are designed to separate certain minerals and chemicals from the water.

    Then, the purified water flows through the second set of membranes. This time, the membranes are designed to remove any remaining contaminants.

    An activated carbon filter doesn’t have these two sets of membranes. Instead, it uses carbon particles to absorb impurities.

    Reverse osmosis systems are more expensive than activated carbon filters. However, they’re also more effective.

     

  • Which Filter Is Better For Removing Lead?

    That really depends on your needs. If you’re worried about lead levels in your home, then you’ll probably want to invest in a reverse osmosis or carbon block filter.

    However, if you just want to reduce the taste of chlorine in your water, then you might be interested in buying a cartridge filter or a unit that combines multiple forms of filtration.

     

  • Why Does My Tap Water Taste So Bad?

    There are many reasons why your tap water could taste bad. It could be because there aren’t enough minerals in the water. Or maybe the pipes are old and corroded.

    Or maybe it’s because you live near a chemical plant. Whatever the reason, you can fix it with a good quality water filter.

     

  • I'm Having Trouble Finding A Good Filter. What Should I Look For?

    When shopping for a water filter, make sure that it has high flow rates. Also, check out its warranty. Some manufacturers offer warranties of 1 year or even 2 years.

    Some companies even offer lifetime warranties. So, if something happens to your filter, you won’t have to worry about replacing it.

    Another thing to keep in mind is whether or not the company offers customer service. Many people find it frustrating when their filter stops working after only a few months.

    But if you call the manufacturer, they’ll usually send someone out to replace it.

    So, before you purchase a new filter, make sure that you research the company first. You don’t want to end up with a lemon!

    But most importantly of all, you need to find out what contaminants a filter is capable of removing from your water. Different filter types are effective in different ways, so you need one that’s fit for purpose.

     

  • Do I Need To Change My Water Filter Every Month?

    No, you shouldn’t need to replace your filter every month. In fact, you can get away with changing it once every 2 to 6 months. That way, you won’t run into problems down the road.

    However, if your water tastes terrible, or if you notice mold growing around your filter, then you should definitely change it sooner rather than later.

     

  • How Do I Know Which Filter Is Best For Me?

    The best way to figure out what type of filter is right for you is to look at what kind of water you have, and what kind of water you want.

    For example, if you have hard water, and want soft water, look for a filter that softens water as well as removes contaminants.

    On the reverse, if you’re not worried about hard water and want a filter that will solely remove contamination, then look for one that has an activated carbon filter.

    Also, consider how often you plan to use your water filtration system. Do you plan to drink from it all day long? Or do you plan to boil some pasta of an evening?

    If you plan to consume large amounts of water every day, then you’ll want to buy a larger capacity filter. But if you’re going to use your filter less frequently, then you may want to go with a smaller model.

     

Final Thoughts

A great deal of bottled water sold today does not meet current standards, according to new findings by Consumer Reports.

The consumer advocacy group tested dozens of popular brands here and found that many contained levels of chemicals that posed a cancer risk.

So more people are turning to filtering their own tap water for purity, which is a great way to combat this. 

Lead is one of the most dangerous contaminants to ingest. It can cause serious health issues such as brain damage, kidney failure, and even death.

That’s why it’s important to install a water filter that removes lead from your drinking water.

You can also add other types of filters to your home. For example, you can buy a UV light filter to kill bacteria in your water.

And if you’re concerned about fluoride, you can buy a carbon block filter to remove it. It’s always a good idea to read reviews online before purchasing any product. This way, you’ll know exactly what to expect.

Remember not all water filters will work the same. You may even find that there are recommended models available depending on where you live.

So, be sure to shop around, and choose the one that works best for you.